How to Install a Front Splitter or Lip: Tools, Methods and Mistakes to Avoid
Fitting a front splitter or lip is one of the most popular DIY upgrades, and with a little preparation it is well within reach of many owners. This guide covers the general process, the tools you will want and the mistakes we see most often. Always follow the instructions supplied with your specific part, as the details vary by product and car.
Before you start
Make sure you have the right part for your car. If you have not checked yet, read our guide on how to check body part fitment. Not sure which type you need? See front splitter vs front lip.
Tools and materials
- Jack and axle stands, or a ramp, used safely on level ground
- Socket set and screwdrivers
- Drill and suitable drill bits, if the part requires drilling
- Masking tape and a marker or pencil
- Tape measure
- Isopropyl alcohol or a suitable degreaser and clean cloths
- Automotive double-sided tape or adhesive, if the instructions call for it
- The fixings supplied with the part, plus spares
- Gloves and eye protection
- A second person to help hold the part
Step 1: Inspect the part
Open the packaging and check the part against the order. Look for transport damage, cracks, warped edges or finish issues, and photograph anything unusual before you do anything else. Raise any problem straight away.
Step 2: Test-fit without fixing
Hold the part up to the bumper, ideally with a helper. Check the following:
- Does it follow the bumper edge evenly on both sides?
- Do the mounting points line up?
- Is it symmetrical and centred?
- Does it clear the wheels, tyres and undertrays?
- How low does it sit? Measure the gap to the ground and think about the ramps and speed bumps on your daily route.
Use masking tape to temporarily hold it and step back to look from the front and side. Do this before painting, wrapping or drilling, so that the part is still in an unmodified condition if there is a problem.
Step 3: Finish the part
If the part needs paint or wrap, follow the preparation steps in our unpainted parts guide and allow paint to cure fully before fitting. If your part has to be drilled, ask your painter or body shop whether to do that before or after paint. Drilling through a finished surface can chip it.
Step 4: Mark and prepare mounting points
Mark the position on the bumper with masking tape. Measure from fixed reference points, such as the centre of the bumper and each side, so that it is even. Clean the contact surfaces with isopropyl alcohol and allow them to dry.
Step 5: Fix it in place
Common methods:
- Screws or bolts: a secure, removable method. Use the fixings supplied, and use washers where recommended to spread load on plastic.
- Clips: used where the bumper has existing mounting slots.
- Adhesive tape or adhesive: some products use automotive-grade tape as well as screws. Surface temperature and cleanliness are critical, and tape often needs time to bond fully.
- Support rods or brackets: splitters may use these to take load. Follow the instructions for positioning and tightening.
Tighten gradually and evenly. Over-tightening can crack plastic or crush the part.
Step 6: Check ground clearance again
Once fitted, roll the car onto a ramp or a gentle slope and look at the approach angle. If the part is too close to the ground, adjust its position within what the instructions allow.
Step 7: Final check
- Are all fixings tight?
- Is the part level and centred?
- Does it rub against anything when turning?
- Does anything vibrate when you drive slowly?
After the first few drives, re-check the fixings.
Mistakes to avoid
- Not test-fitting first. This is the most expensive mistake.
- Drilling without measuring. Measure twice, drill once.
- Applying tape to a dirty or cold surface. It will not bond properly.
- Over-tightening fixings. This can crack ABS, fiberglass and carbon.
- Working under a car that is only held by a jack. Always use axle stands.
- Ignoring ground clearance. Think about your daily route.
When to ask a professional
If the part's instructions call for trimming, the part needs significant finishing work, or you are not comfortable working under the car, a body shop can do the installation quickly and safely.
Frequently asked questions
How long does installation take?
It depends on the part and your experience. Allow extra time for test-fitting and, if needed, painting.
Do I need to drill the bumper?
Some parts use existing mounting points or adhesive, while others require drilling. Check the instructions for your product.
Is adhesive tape enough?
Follow the manufacturer's instructions. Tape alone may not be intended for every part, so check what is recommended.
Will it affect my warranty or inspection?
Exterior modifications may be subject to local rules. Check your local regulations and, if relevant, your insurer.
Ready to upgrade your front end?
Questions before you order? Contact us.